* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
On my Honda NSS 250 mf 06 maxiskooter, when the steering wheel was turned too hard, the windshield was touched by the risk of breaking it off. I installed the Ai-net Mirror Adapter (10 mm thread, 1.25 pitch) to the right and left. As a result, the mirrors began to be above the fairing . Adapters are made of high quality, most likely stainless steel. They look good, the exterior of the scooter does not break.
I wanted a height for Left's Mirror, so I bought it. It can be firmly fixed to the Clutch lever, Quantity : Pair (for Left and Right) I am satisfied because I became Symmetry. Speaking of greed, if the shape is not hexagonal but rounded, I think I'm getting more Motorcycle.View Detail
[Was there anything that disappointed you? Because the Screw of Mirror is too long or the Adapter has bottomed out, I put a bolt on it I did Do you have any wishes or improvements you would like to make for the Manufacturer? If the female thread on the Mirror side is longer, BEST [Do you have any products to compare it to? None
Frequently Asked Items What made you decide to buy? I don't know if there is an 8mm Mirror set screw or a 10?Handlebar set screw adapter No How was your experience with it? perfectly (suited) Was the installation difficult? None 【Please tell me the installation point and hang】 None [Was the Instruction Manual easy to understand? None [Included Parts:were they on? Warranty Is it really necessary? [Others] So it's currently out of stockView Detail
Replaced with a Plating Mirror and put it in the same Chrome plating Adapter Changed, there is no plating failure etc. which is common in cheap ones, and pre-treatment of plating The post-processing is well done, no unevenness, no swelling, no fogging, and the forging process is well done It is a good buy at this price I believe that a motorcycle that is well cared for can keep its quality for a long time It is very comfortable to use with a domestic plating mirror The shortness of the mirror and the length difference between the other side of the mirror without an adapter is very noticeable It fits in the Small limitView Detail
I wanted a height for Left's Mirror, so I bought it. It can be firmly fixed to the Clutch lever, Quantity : Pair (for Left and Right) I am satisfied because I became Symmetry. Speaking of greed, if the shape is not hexagonal but rounded, I think I'm getting more Motorcycle.View Detail
Attached to the CHOINORI Napoleon which was left in the parts box I made it properly although it is as it is made It is the best cospa It's safe to have a half-year warrantyView Detail
Because it fell down and OEMMirror broke, I attached Napole On Mirror to LITTLE CUB, but it was hard to see the rear part compared to the OEM compared with the height. So I purchased this item, but as a result it did not change much. I regret to pick up rust soon. Material : I want the item of Stainless Steel. View Detail
On the 2001 Honda Forza MF 06, after 15,000 km, the suspension bearing of the right rear wheel hummed. Replaced with NTN products. After that I drove 3000 km, I'm happy with the result. When pressing in the bearing, so that the seat does not wobble, you first need to heat the suspension part with an industrial hair dryer to a temperature of 150 degrees C. This product has a metal protection for the balls, bearings with a plastic ring are installed on the scooter at the factory.View Detail
This chain is used on a Honda MTX 50 and is used in tough off-road conditions. In the mountains, in swampy areas, when overcoming water obstacles up to 0.5-0.6 m deep, the DID STD Series Chain 420D Steel shows itself only positively. It retains its size (does not stretch) when used in enduro conditions no less than for 1000 km.At the same time, it works constantly in mud and with a lack of lubrication.View Detail
After 10 years of operation of the maxiscurator, the grease dried up in the drain bearings and they became unusable. A play appeared on the wheel. I replaced them with Koyo bearings. I need to remove old ones and put new bearings on the wheel’s hot disk, it must be heated with an electric hairdryer. After replacing the bearings Koyo passed 5000 km without any problems.View Detail
Iridium candle was installed on a 2-stroke air cooling Suzuki K 125 motorcycle. The engine on it starts confidently, works well both at medium (3500-4500) and at high speeds (7000-8000). There are no spark plugs in the ignition. The engine pulls well.The carburetor adjusted to a normal mixture, not poor and not rich, brown soot, the motor does not overheat.View Detail
I installed this tubeless tire on the rear wheel of a Honda GL 700.There is 1-1.5 cm distance to the left and right pendulum. The sides are rigid, which makes it very difficult to mount the tire on the rim independently. This work is easily done in a car service using a tire mounting machine .View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING