Push cancel type indicator switch Headlight Hi / Low switching switch With Passing Switch Compatible with headlights with position lamps Headlight always-on type compatible Exclusive for 12V vehicles Black surface specification Compatible with vehicles produced on or after April 1, 1998. Harness length: 570mm Housing mounting width: 45mm
*Special connector is included for 12V Monkey, Gorilla and BAJA with side stand switch. ・Not applicable to previously sold combination switch assemblies. ・This method of use is for racing only. ・This method cannot be used for Monkey (FI). *Depending on the lot, the product may be delivered with the old price and label with the old JAN code before the price change.
This is a combination switch with all the switches on the left side and a push cancel type indicator switch. It can be installed without any wiring work by using the attached dedicated harness. When installing this product to a stock clutch, SP Takegawa special clutch or dry clutch at the same time, you will not be able to use the stock clutch lever and stock clutch lever holder, so you will need to purchase SP Takegawa clutch lever & holder and clutch cable separately.
■When using the 12V Monkey Gorilla (carburetor) combination switch assembly. (05-09-0016) as a race exclusive part: If this combination switch assembly is used to turn the headlights on and off in endurance races where the "light on" instruction is given, it may cause overcharging of the battery or failure of the regulator.SP Takegawa has developed "Metal Clad Resistor" to be used in such a race. By installing this metal clad resistor at the same time, you can prevent the battery from being overcharged and the regulator from failing when the headlights are turned on and off, and maintain the charge balance of the vehicle.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I'm very happy with the Large because it has Push cancellation, Passing, and other features that the OEMs don't have, and it looks more expensive than the competition.View Detail
It is good that the attached Wiring diagram is easy to understand. It is diversion of another company. HarnessCoupler All in chopped Connected directly with Bullet Terminal terminal. Width 45 mm, depth about 60 mm, height about 80 mm Harness With a total length of 30 cm There is a case of Short handle Wiring process is a little annoying because it is too long. Up Handlebar may be exactly right. If it is compatible model you can use immediately with CouplerBolt-on. Gray (Ash) Wiring connects Plus line from Blinker relay.View Detail
Since it was cheap, it purchased. Although it could use ordinarily, there were some portions felt if structure is coarse. I think that it seldom turns to a dress-up up.View Detail
It just said that it was reasonably priced well. It compares pure and texture is low. A scar (size like a pin hole) of paint application and the size of a handle attachment part have a difference a little (the handle pipe side is a smooth.). With [ use ] no problem. It is not beautiful. Paint application is also thin and understands the granularity of a ground for a part. The point which can be evaluated is three points of a long time of lightness, lever form, and a lever. Well, as functional parts, it will be buying it. I consider that it is better to stop as an object for an ornament.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!