[Specification] ・It supports up to Daytona RideBar (MID) with 760mm (29240) ・Grip end penetration type
*APE needs to be converted to disc brakes. *APE requires a separate brake lever holder.
<> *After installing the product, it is necessary to drain the oil in the oil pump and to block the oil inlet on the carburetor manifold side. *When using this product on the TZR50/R and TZM50R, the cable length is not long enough for the stock carburetor, so it is necessary to replace it with a big carburetor. *There may be changes in product specifications due to the manufacturer's reasons.
Φ20-Φ28 Designed for optimum take-up of various big cabs! Φ20-Φ28 Super high throttle kit designed for the optimum take-up volume for various big cabs (PE, PWK, VM, PC, CR-mini, VM, Yoshimura YD24/28). In the case of the Φ28 carburetor, it takes about 55 degrees of rotation to fully open. For use with the NSR50 and NS-1, it can be used with either the stock carburetor or the Daytona big carburetor kit.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
Recently viewed products
Ratings & reviews for this product or related products
I bought this High Throttle for my Honda RS150 that fits perfectly. The quality of the item and the finish is great. I have to modify the item as i instaled it in a throttle body rather than the carb recommended but it still fit fine. This is cheap throttle an alternative throttle for a premium throttle. The item is package nicely. It was ship wraped in bubblewrap so item is protected. Make sure that the length of the cable is compatible witj the motorbike your going to use. View Detail
I thought that it was good for the repair measure of the accelerator wire off of my friend's SUPER CUB C50 modified 124ccPipe HandlebarSpec. and introduced it. The carburetor and accelerator wire of a certain Horizontal TypeEngine 124cc Full kit became bad, and the carburetor was changed to YD28. The taking out position was changed, and it became better temporarily, and it was relieved. However, when I heard that Axel didn't return after switching back, and I visited to check, I found that there was a dislocation of the Accelerator Wire attachment part of the Switch box original. I have repaired and adjusted the handlebar many times, but the angle of the handlebar cut, the length of the wire, and the position of the fitment were not good, so I gave up and considered a new installation. I picked up a few kits that are hard to remove, easy to adjust, have long guide wire, high solo, and repair parts available, and have standard long wire that corresponds to the length of CUB frame. At any rate, I'll replace the Grip at his request, and until he has more time. "Take the Small stuff home and work out the tentative matches and Ideas. So, I worked on it. This is a perfect feeling. I'm looking forward to installing everything into the car and driving it in the real world.View Detail
It was the same product until now but Wire was somewhat elongated so I purchased it as a spare. Since 2 St Parts are decreasing, I think that I want to use it for Large.View Detail
Hi all,This throttle, grips and cable are great quality, great fit and finish, East to install. I would highly recommend this product to anyone looking for a good quality throttle.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!