[Quantity] 1 piece [Compatible stock part number] 3TU-83550-01
* The image is only for reference. The image shown may differ from the actual product.
[Ensures high quality compared to stock parts] Suitable for a wide range of bikes from scooters to large bikes. The quality of our products is equivalent to that of stock OEM products. The cable parts are essential for smooth riding, so be sure to try the high quality NTB cables. STANDARD&TERMINATER CABLE To ensure proper clearance of the inner wire, the housing is wrapped with reinforced steel. All cables use nylon sleeving to ensure long life and smooth operation.
STAINLESS STEEL BRAIDAD&ARMOR COAT CABLE Covered by tightly woven stainless steel. This cover has the shine of a fine metal and provides protection against various damages. Armourcoat cables have a crystal clear coating that prevents scratches on painted or chrome surfaces of the bike.
STANDARD COIL-WOND
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I decided to purchased this speedometer cable because of the low price.The build quality almost same as the OEM cable and OEM cable just a little bit pricey than the NTB version.It's been 6years since I first change my bike's(TW200) speedometer cable.So Time Has come to change it.At some times when I was traveling at a speed of more than 80 km/h, I noticed that the needle on the speedometer bouncing back just a little bit.I want to replace the old speedometer cable because I got a brand new speedometer cable from WEBIKE SHOP. Before I remove the old speedometer cable ,First I had to remove the headlight plastic shell and unplug the wiring connector then removed the headlight lamp.SO it was very easy to reach the speedometer cable and unscrew from the speedometer .Then squeeze the speedometer clip/ Remove small clip at bottom of cable housing and free the old speedometer cable from the groove in the brake panel..Before I installed the new speedometer cable ,pull speedo cable out of housing and apply grease (I had tube of waterproof lithium grease handy) to cable as your feeding it back in housing. turn and wiggle it back in all the way.apply a light coat of waterproof grease to the speedometer O-ring ( Brand new speedometer cable doesn't have an O-ring).Install the Brand New speedometer cable into the brake drum and then install the speedometer cable clip into the groove in the brake panel.make sure clip in right by gently trying to pull housing back out.Then need to tighten the upper cable that goes direct to the speedometer itself. 10 minutes Job .After installing the new cable speedo needle has no bounce and steady as a rock on smooth roads.AS ALWAYS THE PACKAGE ARRIVED ON TIME FROM JAPAN AND VERY NICELY PACKED.THANKS FOR THE SUPPORT WEBIKE.Awesome Online Shop.If anyone need parts for your bike Webike Shop is the Best place.Reasonable Prices and 5Star Shop. Cheers ! View Detail
[How is it used? Used for HORNET250; Meter needle was shaking, so it was replaced at the same time as OEM Product's Joint. How was your experience with it? So far, it has been used without any noticeable drawbacks or problems. How did it compare to other products? I think we can say OEM Product same etc. [Points to note] When replacing the HORNET meter cable, it is necessary to remove the tank, so some knowledge and tools are required.View Detail
[How is it used? While running, the Speedometer suddenly stayed at Zero, and when the Cable was removed, it was replaced because it was twisted off. Chose this one because the OEM is discontinued and not sold.
Was the one you received as per Image? Yes Was the installation difficult? No, sir. However, it is difficult without any work experience at all, such as the need to remove the Meter. How was your experience with it? Normal. Perfect. Very Smooth rotation.
[Included Parts:were they on? None
[Was there anything that disappointed you? None Other items that would be helpful You can choose to do so with complete peace of mind. With this Cable, you can ride all the way.View Detail
I ride it mostly for commuting. KLE250." But I was looking for an OEM Product because my Cable ran out. But I can't find the OEM, so... KLE400." Purchase this product, which can be used in After receiving it, he immediately took it to Motorcycle shop for replacement. I thought what if the Cable seemed to sag, but it is Large sturdy even after driving 150km since the replacement.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!