- Fits:
- YAMAHA FZ1 16 S
- YAMAHA FZ1 15 S
- YAMAHA FZ1 14 S
- YAMAHA FZ1 13 S
- YAMAHA FZ1 12 S
- ...and more.
I used to use Anodized Finishing, but the color faded and peeled off, so I decided to use Material:I chose Plastic. The color does not fade, does not peel, and is offset, so when you hang a hook on it...Read More - Fits:
- YAMAHA FZ1 16 S
- YAMAHA FZ1 15 S
- YAMAHA FZ1 14 S
- YAMAHA FZ1 13 S
- YAMAHA FZ1 12 S
- ...and more.
I purchased this product to improve the appearance of the image rather than to maintain it. It was a good decision to buy it.Read More - Fits:
- YAMAHA FZ1 16 S
- YAMAHA FZ1 15 S
- YAMAHA FZ1 14 S
- YAMAHA FZ1 13 S
- YAMAHA FZ1 12 S
- ...and more.
It was installed on the Swing Arm of DL1000 V-STROM650, and it is also used on DL1000 V-STROM1050XT after the vehicle replacement.I used a V-Hook for my JTrip Rear stand, which makes it easy for one p...Read More - Fits:
- KAWASAKI ZX-25R 20-21
- SUZUKI KATANA 19-21
- SUZUKI BANDIT1250
- SUZUKI BANDIT1250F
- SUZUKI TL1000S
- ...and more.
It has a V-shaped receiving groove for easy STAND-hookingIt's very handy because I can stand up when I remove the wheel and wash the carI leave it on after I put it on, but it doesn't come off or inte...Read More - Fits:
- SUZUKI GSX1250F 10-
- SUZUKI BANDIT1250F 10-
The protrusion from the body of the car is not too noticeable because it is only Slider part To install, remove the Under Cowl, remove the Radiator and replace the Fan cover It takes a lot of time and...Read More - Fits:
- SUZUKI KATANA 19-21
- KAWASAKI ZX-25R 20-21
- SUZUKI BANDIT1250F
- SUZUKI GLADIUS650400
- SUZUKI BANDIT1250
- ...and more.
Previously I was wearing AGRAS, but I have flaked away so I bought a new one this time. Even though RED was a bit more vivid, the shape is not complain.Read More - Fits:
- SUZUKI BANDIT1250F (BANDIT1250F) 10-16
I am wearing BANDIT 1250 SF.Because it has a heavy weight Motorcycle so I put on the meaning of insurance and I am wearing it from car delivery.I liked the shape the most compared to those of other co...Read More - Fits:
- SUZUKI BANDIT1250F (BANDIT1250F) 10-16
I got stood up.. Maybe because I was right beside Motorcycle, it may be because I was supported a little, but I did not have one scratch on the car body. I think it depends on how to fall but there is...Read More - Fits:
- KAWASAKI ZX-25R 20-21
- SUZUKI KATANA 19-21
- SUZUKI BANDIT1250
- SUZUKI BANDIT1250F
- SUZUKI TL1000S
- ...and more.
In doing ChainMaintenance, I was looking for Stand Hook.I decided on this product on condition that there is trust, which is functional priority rather than appearance priority.It is easy to install, ...Read More - Fits:
- SUZUKI BANDIT1250F (BANDIT1250F) 10-16
carrying out right [ of the Design ], if it reaches in search of an Engine slider variously -- also throwing away -- it was easy.It was good to purchase a LSL Mounting kit.Because a kana ? SLIDER50 He...Read More - Fits:
- SUZUKI GSX1250 F 10
Although the SLIDER50 of LSL was attached, since it spoiled in the accident, this product was purchased.If it is the generator Clutch-cover protection purpose, the direction of LSL thinks that it is ...Read More - Fits:
- SUZUKI BANDIT1250
- SUZUKI BANDIT1250F
It prepared for the Circuit run meeting and attached for the Damage mitigation to a car body at the time of an emergency fall.
Although the description was not contained in goods, it was attached sim...Read More - Fits:
- SUZUKI BANDIT1250F
- SUZUKI BANDIT1250
Since the motorcycle store was told that there were many people who thrown and exchange tfld=logit, it equipped for ABS protection. Since the bolt of a cap is only tightened from right and left, it ca...Read More - Fits:
- SUZUKI BANDIT1250F (BANDIT1250F) 10-16
It chose by the low price of appearance and a price. Since it is not necessary to make a hole in a cowl and also and the whole design is not broken down and also color was also chosen, it chose. Since...Read More - Fits:
- SUZUKI BANDIT1250F (BANDIT1250F) 10-16
Since it attached by bolt on even if it did not process it into a cowl, it opted for purchase. It has attached in about 30 minutes. Since mounting was short anxious about die length at the time of a f...Read More - Fits:
- SUZUKI BANDIT1250
- SUZUKI BANDIT1250F
Back was also attached for the time being. Together with a stand hook slider, I think that it became good touch. However, do I feel [ not much unnecessary ] as? Although in addition the shaft of sligh...Read More - Fits:
- SUZUKI BANDIT1250F
Bandit1250F was equipped. The black anodized of the option is applied. It is the touch out of which a sense of togetherness may come.Read More
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING