*The image shows the seat cover reupholstered.In addition, the image is an image. *This product does not include the seat assembly (seat itself). *A tacker is required for installation of this product. *The product is designed exclusively for the models and produced with emphasis on the texture after reupholstering.When you reupholster the seat, you may think that the seat cover is a little bit small, but it is because we produce the product very tightly to emphasize the quality. *If the seat of your vehicle is an aftermarket one, it may not be able to be installed, so you need to check before purchasing. *The color of the fabric and other materials (piping, etc.) may change slightly depending on the time of purchase.
* The image is only for reference. The image shown may differ from the actual product.
This product is designed for exclusive use in models. From the production of the seat mold to the purchase of the fabric, cutting and sewing are all done in Japan (by Grondeman), and the Grondeman staff has made this seat cover in Japan without any compromise. The reupholstered seat is a faithful reproduction of the seat of the vehicle, so the quality of the reupholstered seat will be the best. If you have a hand tacker (the core of it), a thin flathead screwdriver and radio pliers (to remove the core), you can reupholster it. Once you learn how to do it, you may want to try different designs of seat covers. (Please be careful not to injure yourself with the core of the tacker when re-covering.)
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I reupholstered the Seat of the last model FI LITTLE CUB. The Rubber Type is easy to work with and requires no tools, but if you want to make your own chain I want to reupholster it well, so I chose this one.
Because LITTLE CUB of our house is all penned to Yellow color & Black, it is in the meaning of Coordinates. Yellow Color Piping & Color:I decided to go with Emboss in Gray. I was prepared for the delivery time as it was a special made-to-order item, but it arrived in about two weeks.
The instruction manual is written in the package and there is also a video guide. The guidance was very detailed and reassuring.
1. Remove the Seat from the car body (NutQuantity of 10mm):2pc. (Set) 2. Remove the conventional Kaw (with Slotted screwdriver and Pliers) 3.The fixing of the reupholstering Seat is back and forth→Quantity:Pair (for Left and Right) and stop it with Tucker while pulling on the diagonal. (You can also use HandTucker, but I used Air Tucker, 10mm wide and 6mm long.
The difficulty of reupholstering Seat in CUB is low. It's hard to make a mistake the first time if you make a firm decision not to rush into a Wrinkle.
Also, when you remove the leather from the Normal seat, there is a Vinyl sheet sandwiched between the surface of the Sponge Do not throw this away, use it as is. If the Vinyl is deteriorated or torn, you can use the Vinyl bag as It would be better to cut or otherwise tuck it in. Having Vinyl underneath will prevent rainwater from seeping into the Sponge through the seams when it gets wet, or seeping out through the seams when you sit on it. The work took about 20 minutes to complete.
About color I thought that BlackEmboss is not white, and I dared to use full EmbossColor!:I went with the Gray color, which I kind of regret. The actual product is brighter than the Image in the product photo, so it looks a bit dirty. I should have made a safe Black & Yellow color Piping...
There are some cheap SeatAssy available in Asia, but the Urethane foam is hard. If you are OK with the STD Shape, you may want to reupholster it because the seating comfort will be different from the OEM.View Detail
OEM's VTR 250's Seat is hard and painful, so Urethaneetc. I adjusted it and it deteriorated while buying it. Although I thought that it is hard to work because impression that I purchased it did not have a mold, unexpectedly the fabric was softened many times and adjusted and it gradually became familiar with the warmth of my hands. Put it down overnight and put a light squeeze again and testRAN done. Once I got on Touring to GW and confirmed Fitting again a little deflection came out so we planned to finish the adjustment at the point where the growth stabilized for a while. Hang of the tightening method temporarily fixes the front side of Seat only at both ends, semi-fixes the Tandem side of Seat, temporarily fixes the SIDE part to trace shape, and makes the whole circumference Quantity : Pair (for Left and Right) Hitoshi etc. While tightening while stretching, during this time Tucker fixed and unfastened repeatedly readjusted. I think that it is important to judge that the elongation of the dough will stabilize after a long time. Finally, the usability is normal fabric and EmbossSpec. I was worried about which to do, but Emboss has a moderate Grip feel and feels good. This maker purchased ordinary fabric for CUB, but the fabric was still thick and slippery. I think it is a correct answer for Emboss. It is only after durability.View Detail
I was doing a Cover Type on Seat of OEM, but wear of SIDE section occurred, so I bought a Cover of Cover Type this time. Purchased for LITTLE CUB in MD50. Size can be installed without problems. Cover 's fabric is equivalent to OEM and quality is likely to be good internally. Concerning durability in the future. However, Seat of MD is a type that claws cling to the base plate of iron plate and catches the fabric there and squeezes it up. Since there is no durability of the nail, there is a possibility that the nail may break due to rust of the base plate unless it is set to Cover Type next time. Regular Motor If it is a Type Seat that can be replaced with Tucker, it is recommended as a regular replacement part.View Detail
The NORMAL epidermis became hard, and it turned out to be double stitch, because it plays an anko so it looked emphatically. 【How was it actually used?】
Emboss was easy to grow and Sverane was not easy to stretch, but even an amateur could handle it somehow. Sitting comfort is very good. Anco is also used for Motorcycle Seat Material "BodyDoctor" I forced a rough pillow. Grom Seat of torture became a high-class Sofa and it looks better and it is highly self-satisfied. 【Was it difficult to install? (Hard parts case)】
HandTucker sometimes loses its foundation and the core does not get stuck. I think that if you have Air Tucker you can change it comfortably. 【Please tell me the point of installation and hang (in the case of Hard parts)】
As I noted above, HandTucker uses a lot of grip strength. Should be challenged with the preparedness to redo many times without sticking. If you do not want, I recommend using Air Tucker or Electric Tucker. 【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) ] [Is there anything I was disappointed about?]
At first we arrived in the case of the cylinder and I was worried about the crease. Because I put up for the bread in the anko bulk, I did not care about the folds. 【Hope for Manufacturer - Please let me know if you have any improvement points] Because the price was 4000 yen due to mistake in PC setting, we called and confirmed Manufacturer w When I did this price I was even more satisfied with w 【Have you compared items?】 None [Others] Grom 's pain was also good and I got a good Seat.View Detail
There is Tucker as necessary for reconnection, but unexpectedly it is enough for Daiso's It ended with the result.
I think that there was no mention, but as Tandem belt was also attached It was good.
Size feeling was made quite Exactly, so it was a pain to stretch wrinkles There is thickness, let's put the spirit in because it is also comfortable to touch if you can stretch it cleanlyView Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!